PART.................................................QUANTITY         CALL OR EMAIL FOR PRICE

CYLINDER GROUP

CYLINDER (PORTED)..............................1
HEAD...........................................................1
COOL HEAD (OPTION)............................1
INTAKE ADAPTER..................................1
EXHAUST ADAPTER .............................1
LINER * ......................................................1
PISTON........................................................1
RING.............................................................1
CIRCLIPS.....................................................2
WRISTPIN...................................................1
CARBURETOR...........................................1
CARB. GASKET.........................................1
HEAD O-RING (SILICON)........................1
10-24x3/4 BOLTS........................................6
8-32X1/2 BOLTS.........................................2
10-24X1/2 BOLTS.......................................2
10-24X5/8 BOLTS.......................................4
3/16 DOWEL PINS.....................................2
WATER FITTINGS....................................4

* * MUST BE SENT IN FOR FACTORY INSTALL

CRANKCASE GROUP

CASE..............................................................1
INNER BEARING PLATES #1................2
OUTER BEARING PLATES #1................2
MAIN BEARINGS........................................4
OUTPUT SEAL PLATE #2.......................1
IGNITION SEAL PLATE #2......................1
SEALS.............................................................2
BIG O-RINGS (BUNA-N)...........................2
SMALL O-RINGS (BUNA-N) .....................4
3/16 DOWEL PINS........................................4
1/4-20X3 1/4 BOLTS.....................................4
1/4 WASHERS...............................................8
1/4-20 NUTS...................................................4

#1 NO BEARINGS INSTALLED

#2 NO SEALS INSTALLED

2-07-05
------------------------------------------------------------------------------------------------------------------

CRANKSHAFT GROUP

COMPLETE CRANK....................................1
IGNITION WHEEL ASSEMBLY.................1
OUTPUT WHEEL ASSEMBLY...................1
IGNITION SHAFT *.....................................1
OUTPUT SHAFT *.......................................1
CRANK PIN *................................................1
ROD (NEW STEEL ROD WITH UPPER BEARING)..1
THRUST WASHERS.....................................2
LOWER ROD BEARING...............................1
6X25 MM STUD (NON CLUTCH) .............1
1/4-28X5/8 BOLT............................................1

* * MUST BE SENT IN FOR FACTORY INSTALL

IGNITION GROUP

SOURCE COIL................................................1
IGNITION COIL..............................................1
FLYWHEEL......................................................1
IGNITION COIL MOUNT..............................1
SOURCE COIL SPACERS..............................2
SPARK PLUG...................................................1
SPARK PLUG BOOT.......................................1
5/16-18X1 BOLT...............................................1
5/16 WASHER..................................................1
8-32X7/8 BOLT.................................................2
8-32X5/8 BOLT.................................................2
8-32 NYLOCK NUT..........................................2

PULL STARTER GROUP

PULLSTARTER................................................1
PULLTANG.......................................................1
FLYWHEEL COVER.........................................1
PULLSTARTER STANDOFFS.......................4
6X16 MM BOLTS.............................................2
8-32X2 BOLTS..................................................4
8-32 WASHERS................................................4

2-05-06
-----------------------------------------------------------------------------------------------------------------

EXHAUST GROUP

TUNED PIPE (HP).........................................1
SILENCER........................................................1
SILENCER SPRINGS......................................2
O-RINGS (SILICON) ......................................2

MOTOR MOUNT GROUP

COMPLETE MOUNT......................................1
UPPER MOUNT PLATES..............................2
LOWER MOUNT ANGLES.......................... 2
RUBBER MOUNTS........................................4
5/16-18X3/8 BOLTS........................................8
10-24X3/4 BOLTS...........................................4
#10 WASHERS...............................................4
8-32X3/8 BOLTS.............................................8

MISCELLANEOUS

O-RING KIT w/ carb. Gasket.........................1
BOLT KIT........................................................1
TIMING TOOLS..............................................1

11/08